Iai-america IK Series Manuel d'utilisateur télécharger pdf (Page 13)

XYB + base fixed type: Double slider type

IK3-S(P)BBD

DWG. No. GMM07-059E 1/2

* This assembly procedure applies to combination direction 1. With other combination directions such as 2 through 4, the actuator and bracket directions are different. If you are using combination direction 2 through 4, assemble

the parts by referring to this drawing.

Model

Parallel pin

Hex

socket-head bolt

Tightening torque

∅8h7 x 18

M8 x 20 mm

Model

Parallel pin

Hex

socket-head bolt

Tightening

torque

∅4h7 x 10

M5 x 15 mm

Model

Parallel pin

Hex head bolt Tightening torque

∅8h7 x 18

M8 x 20 mm

Note: z Although the corners of each part have been chamfered, exercise due caution during

assembly to prevent injury. If necessary, wear gloves and other protective gears.

z Exercise due caution durin

assembl

revent

inchin

our hands and fin

ers.

[Tools] Allen wrench, spanner wrench, ruler

[2] Plate X

Parallel pin (2 pcs)

X-axis

Screw lock holes

Parallel pin holes

Hex socket head

bolt + plain washer

(8 pcs)

Screw lock holes

Parallel pin holes

Screw lock holes

Combination directions 1, 3

Combination directions 2, 4

Note: To ensure squareness of the X-axis and Y-axis, place one

parallel pin.

After adjusting the squareness of the X-axis and Y-axis,

ffix

x h

ead

With combination directions

2 through 4, the bracket

direction is different.

Hex head bolt +

high-tension

washer (6 pcs)

[1] XY bracket

[2] Plate X

Parallel pin

(1 pc or 2 pcs)

X-axis

Screw lock holes: ∅9

Parallel pin holes:

∅

Screw lock holes:

∅

Screw lock holes: ∅9

With combination directions 2 through

4, the actuator direction is different.

Y-ax is

Parallel pin (1 pc or 2 pcs)

X-axis

[2] Plate X

[1] XY bracket

Hex socket-head

bolt (4 pcs)

Model Parallel pin

Hex socket-head

bolt

Tightening torque

∅5h7 x 14

M5 x 12 mm

Note: To ensure squareness of the X-axis and Y-axis, place one parallel pin.

After ad

ustin

the s

uareness of the X-axis and

-axis

affix the hex head bolt.

Parallel pin (1 pc or 2 pcs)

[1] XY bracket

[2] Plate X

X-axis

Screw lock holes:

∅

5.5

Parallel pin holes:

∅

Screw lock holes:

∅

5.5

Y-ax is

[3] Plate YZ1

Hex socket-head bolt

(4 pcs)

After installing plate

YZ1, move the Y-axis

slider toward the

counter-motor end.

Model Parallel pin

Hex

socket-head bolt

Tightening torque

∅4h7 x 10

M5 x 12 mm

Parallel pin (1 pc or 2 pcs)

Z-axis

Hex socket-head bolt (4 pcs)

[4] Plate YZ2

Note: On some models, only one parallel pin may be accommodated depending on the axis.

Screw lock holes: ∅5.5

Parallel pin holes:

∅

Screw lock holes: ∅5.5

Model Parallel pin

Hex

socket-head bolt

Tightening torque

∅4h7 x 10

M5 x 10 mm

Screw lock holes: ∅5.5

Parallel pin

holes: ∅4

Parallel pin

holes: ∅4

Parallel pin

holes: ∅4

Parallel pin

holes: ∅4

Screw lock holes: ∅5.5

Parallel pin (1 pc or 2 pcs)

Z-axis

[4] Plate YZ2

Y-ax is

[3] Plate YZ1

Hex socket-head

bolt (4 pcs)

[4] Plate YZ2

[3] Plate YZ1

Note: To ensure squareness of the Y-axis and Z-axis, place one parallel pin.

After ad

ustin

the s

uareness of the

-axis and Z-axis

affix the hex head bolt.

Model Hex socket-head bolt Tightening torque

M4 x 8 mm

The following procedures apply to configurations with a cable bearer.

Install the X-axis and guide rail X.

X-axis

[5] Guide rail X

lign the end face of

the base with the end

face of guide rail X.

Bottom view

Y-axis

Hex socket-head bolt (2 pcs)

Hex nut (2 pcs)

[8] Bearer mounting bracket 1

X-axis

[5] Guide rail X

[1] XY bracket

Z-axis

Set the dimension from the

side face of the XY bracket to

the tip of bearer mounting

bracket 1

[

]

to 152.5 mm.

1 2 ... 8 9 10 11 12 13 14 15 16

Commentaires sur ces manuels

Pas de commentaire

Iai-america IK Series Manuel d'utilisateur Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Iai-america IK Series