Iai-america XSEL-KX Manuel d'utilisateur Page 246
- Page / 377
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
230
Part 4 Commands
ARCH (Arch motion)
Extension condition
(LD, A, O, AB, OB)
Input condition
(I/O, flag)
Command, declaration
Output
(Output, flag)
Command,
declaration
Operand 1 Operand 2
Optional Optional ARCH
Position
number
Position
number
PE
Perform arch motion from the current point and move to the specified points.
• Move to the points specified in operand 1, via arch motion.
• Movements in directions other than the arch-motion Z-axis direction will begin after rising from the
current point to the start-point arch trigger. After the Z point specified in operand 2 (as the highest
point) is passed and movements in directions other than the arch-motion Z-axis direction are complete,
the axes will pass near the end-point arch trigger and reach the specified point.
• Palletizing arch triggers must be set using an ATRG command.
ACHZ
3
ATRG
13
11
ARCH
10
12
* When the operation is resumed after a pause, depending on the position where the operation is
resumed the locus may follow the lines (dotted lines) indicated by asterisks in the diagram for the
composite section from ascent to horizontal movement or from horizontal movement to descent. Be
careful not to cause interference.
• The arch-motion Z-axis coordinate of the end point will become the arch-motion Z-axis component of
the point data specified in operand 1, if any, plus the arch-motion Z-axis offset. If there is no arch-
motion Z component, the arch-motion Z-axis coordinate of the end point will become the arch-motion
Z-axis coordinate of the start point plus the arch-motion Z-axis offset. (Normally the offset is added to
all arch-motion positions, such as the arch triggers and Z point.)
• An error will generate if the start-point arch trigger is set below the start point or the end-point arch
trigger is set below the end point. (Note: Up/down has nothing to do with +/– on the coordinate
system.)
• The arch-motion Z-axis up direction refers to the direction toward the Z point from the start point (the
down direction refers to the opposite direction), and has nothing to do with the size of coordinate value.
Therefore, be sure to confirm the actual operating direction when using this command.
Highest point of arch motion
Position No. 12
*
*
*
*
Start-point arch trigger
Position No. 13
End-point arch trigger
Position No. 11
Start point
End point
Position No. 10
- X-SEL Controller 1
- JX/KX Type 1
- Operation Manual 1
- CAUTION 3
- Safety Precautions 5
- Warning 6
- Before Use 11
- Table of Contents 12
- Introduction 17
- Part 1 Installation 18
- 1. Warranty Period 19
- 2. Scope of Warranty 19
- 3. Scope of Service 19
- 1. Installation Environment 20
- 3. Power Source 21
- 1. Front View of Controller 24
- 2.1. Application 34
- 2.2. Core 35
- Chapter 5 Specifications 36
- Caution 38
- 4. External Dimensions 43
- 3 - ∅ 5 44
- 77.2 150 150 77.2 125.3 44
- Chapter 6 System Setup 45
- 2. I/O Connection Diagram 47
- 3. I/O Flat Cable 49
- Chapter 7 Maintenance 50
- Part 2 Operation 57
- Chapter 1 Operation 57
- Start signal 59
- Emergency-stop 59
- Parameters 62
- Parameters Parameters 62
- Chapter 1 How to Save Data 63
- Write to flash memory 63
- 1.2 I/O Ports 67
- 1.3 Virtual I/O Ports 68
- 1.4 Flags 70
- 1.5 Variables 71
- 1.6 Tags 74
- 1.7 Subroutines 75
- 1.8 Symbols 76
- 1.10 Axis Specification 77
- 2. Position Part 79
- 79
- 3. Command Part 80
- 3.2 Extension Condition 81
- Part 4 Commands 82
- Confirmation position 91
- 1.2 Arithmetic Operation 96
- Optional Optional MOD 98
- Optional Optional SIN 99
- Optional Optional COS 100
- Variable 100
- Data ZR 100
- Optional Optional TAN 101
- Optional Optional ATN 102
- Optional Optional SQR 103
- Optional Optional AND 104
- Optional Optional OR 105
- Optional Optional EOR 106
- Optional Optional CPXX 107
- 1.6 Timer 108
- Optional Optional TIMC 109
- Program 109
- Prohibited CP 109
- Optional Optional GTTM 110
- (Output 111
- Optional Optional FMIO 119
- 1.8 Program Control 122
- 1.9 Task Management 125
- Currently executed step 128
- Currently paused step 129
- 1.10 Position Operation 130
- Position 137
- Optional Optional PSIZ 141
- X 100 (%) 152
- Optional Optional GRP 155
- Optional Optional DFTL 161
- Optional Optional SLTL 162
- Optional Optional GTTL 163
- Optional Optional DFWK 164
- Optional Optional SLWK 165
- Optional Optional GTWK 166
- Optional Optional DFIF 173
- Optional Optional SOIF 174
- Optional Optional SEIF 175
- Optional Optional GTIF 176
- Optional Optional SVXX 177
- Prohibited PE 177
- Optional Optional MOVP 178
- Optional Optional MOVL 179
- Optional Optional MVPI 180
- Optional Optional MVLI 181
- Start position 182
- Position origin 182
- End position 182
- Optional Optional STOP 183
- Optional Optional PUSH 185
- Center angle 191
- Center position 192
- Optional Optional PBND 193
- Distance CP 193
- Optional Optional TMPI 194
- Optional Optional TMLI 195
- Optional Optional PTRQ 196
- Ratio CC 196
- Optional Optional IFXX 199
- Data CP 199
- Optional Optional DWXX 202
- 1.15 Multi-Branching 204
- Optional Optional WHXX 205
- Prohibited Prohibited WSXX 206
- Optional Optional SYST 210
- Optional Optional GARM 211
- 1.17 Communication 212
- Optional Optional TMRD 214
- Optional Optional SCHA 216
- Character 216
- 1.18 String Operation 217
- Optional Optional SPUT 220
- Optional Optional STR 221
- Data CC 221
- Optional Optional STRH 222
- Optional Optional SLEN 225
- Optional Optional BGPA 226
- Palletizing 226
- Optional Optional PAPN 227
- Pattern 227
- Optional Optional PAST 229
- (Position 229
- Optional Optional PAPS 230
- Optional Optional PSLI 233
- (Count) CP 233
- Optional Optional PCHZ 234
- Optional Optional ACHZ 237
- added to 246
- 1.1 CP Operation 250
- All-axis parameter 251
- CP-operation 251
- 1.2 PTP Operation 252
- 2. Arm System 253
- : Area accessibly only 254
- : Area accessibly only by 254
- 3. Coordinate System 261
- 3.2 Load Coordinate System 263
- 3.3 Tool Coordinate System 267
- –50, Zb = 150, Rb = 0 272
- 50, Zb = 200, Rb = 180 272
- 5. Soft Limits 274
- 2. PATH/PSPL Commands 280
- 3. CIR/ARC Commands 280
- 1. How to Use 281
- 2. Palletizing Setting 281
- A. 3-point teaching method 283
- PX-axis direction pitch 284
- Teach position data No. 100 284
- PY-axis direction pitch 284
- 3. Palletizing Calculation 287
- 4. Palletizing Movement 288
- 5. Program Examples 290
- : 20, zigzag count: 4 291
- 1. Basic Frame 294
- 2. Ladder Statement Field 295
- 3. Points to Note 295
- OUTR301 295
- OUTR302 295
- 4. Program Example 296
- OUTR314 296
- TIMR900 296
- 0.5 SEC 296
- Chapter 7 Multi-Tasking 297
- 3. Program Switching 299
- Appendix 300
- 1 m (1000 mm) 303
- Controller end 303
- Connector not 303
- Control 304
- List of Parameters 307
- 1. I/O Parameters 308
- 3. Axis-Specific Parameters 320
- travel at 323
- 4. Driver Card Parameters 324
- for phase-W current 328
- 5. Encoder Parameters 330
- 6. I/O-Slot Card Parameters 331
- 7. Other Parameters 332
- 8. Manual Operation Types 337
- Trouble Report Sheet 374
- INTELLIGENT ACTUATOR 375
- Catalog No.: ME0119-7A 377
Produits connexes et manuels pour Matériel Iai-america XSEL-KX
Matériel Iai-america TT-C3 Manuel d'utilisateur
(364 pages)
(364 pages)
Matériel Iai-america XSEL-S Manuel d'utilisateur
(544 pages)
(544 pages)
Matériel Iai-america PSEP Manuel d'utilisateur
(116 pages)
(116 pages)
Matériel Iai-america MSEP Manuel d'utilisateur
(296 pages)
(296 pages)
Matériel Iai-america ASEL Manuel d'utilisateur
(468 pages)
(468 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.417 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels