Iai-america XSEL-KX Manuel d'utilisateur Page 363
- Page / 377
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
347
Appendix
(In the panel window, the three digits after “E” indicate an error number.)
Error No.
Error name
Description, action, etc.
D81 Parameter error during calculation of valid target data An invalid parameter value was detected during calculation of valid target data.
Check axis-specific parameter Nos. 7, 8, 138, etc.
D82 Simple interference check zone output-number specification error A value other than an output port/global flag number (0 is allowed) may have
been input, or the specified number may be already used as a system output
number via the I/O parameter for output function selection.
D83
Simple interference check zone number error
The simple interference check zone number is invalid.
E01
DMA address error
DMA transfer error
E02
SCIF send-buffer overflow error
The SCIF send buffer overflowed.
E03
SCI send-buffer overflow error
The SCI send buffer overflowed.
E04
SCIF receive-buffer overflow error
The SCIF receive buffer overflowed. Excessive data was received from outside.
E05
SCI receive-buffer overflow error
The SCI receive buffer overflowed. Excessive data was received from the slave.
E06
Receive timeout error (Slave communication)
Response from the slave cannot be recognized.
E07
SCI overrun error (Slave communication)
Communication failure. Check for noise, circuit failure and slave card.
E08
SCI framing error (Slave communication)
Communication failure. Check for noise, shorting, circuit failure and slave card.
E09
SCI parity error (Slave communication)
Communication failure. Check for noise, shorting, circuit failure and slave card.
E0A
SCI CRC error (Slave communication)
The CRC in the message is invalid.
E10
SCIF communication mode error
The communication mode is invalid.
E11
SCI communication mode error
The communication mode is invalid.
E12
SIO-bridge SCIF send-queue overflow error
The send queue overflowed.
E13
SIO-bridge SCI send-queue overflow error
The send queue overflowed.
E14
SCI receive-data-register full wait timeout error
Communication failure. Check for noise, shorting, circuit failure and slave card.
E15
SCI overrun error
Communication failure. Check for noise, shorting, circuit failure and slave card.
E16
Program end confirmation timeout error
The program cannot be ended.
E17
I/O-processing-program start logic error
The I/O-processing-program start logic is invalid.
E18
Task ID error
The task ID is invalid.
E19
WAIT factor error
The WAIT factor is invalid.
E1A
WAIT logic error
The WAIT logic is invalid.
E1B
Point-data valid address error
Point-data valid address is not set.
E1C
Source data error
The source data is invalid.
E1D Unaffected output number error The unaffected output number is invalid. A value other than an output port
number (“0” is acceptable) may be input in I/O parameter Nos. 70 to 73.
- X-SEL Controller 1
- JX/KX Type 1
- Operation Manual 1
- CAUTION 3
- Safety Precautions 5
- Warning 6
- Before Use 11
- Table of Contents 12
- Introduction 17
- Part 1 Installation 18
- 1. Warranty Period 19
- 2. Scope of Warranty 19
- 3. Scope of Service 19
- 1. Installation Environment 20
- 3. Power Source 21
- 1. Front View of Controller 24
- 2.1. Application 34
- 2.2. Core 35
- Chapter 5 Specifications 36
- Caution 38
- 4. External Dimensions 43
- 3 - ∅ 5 44
- 77.2 150 150 77.2 125.3 44
- Chapter 6 System Setup 45
- 2. I/O Connection Diagram 47
- 3. I/O Flat Cable 49
- Chapter 7 Maintenance 50
- Part 2 Operation 57
- Chapter 1 Operation 57
- Start signal 59
- Emergency-stop 59
- Parameters 62
- Parameters Parameters 62
- Chapter 1 How to Save Data 63
- Write to flash memory 63
- 1.2 I/O Ports 67
- 1.3 Virtual I/O Ports 68
- 1.4 Flags 70
- 1.5 Variables 71
- 1.6 Tags 74
- 1.7 Subroutines 75
- 1.8 Symbols 76
- 1.10 Axis Specification 77
- 2. Position Part 79
- 79
- 3. Command Part 80
- 3.2 Extension Condition 81
- Part 4 Commands 82
- Confirmation position 91
- 1.2 Arithmetic Operation 96
- Optional Optional MOD 98
- Optional Optional SIN 99
- Optional Optional COS 100
- Variable 100
- Data ZR 100
- Optional Optional TAN 101
- Optional Optional ATN 102
- Optional Optional SQR 103
- Optional Optional AND 104
- Optional Optional OR 105
- Optional Optional EOR 106
- Optional Optional CPXX 107
- 1.6 Timer 108
- Optional Optional TIMC 109
- Program 109
- Prohibited CP 109
- Optional Optional GTTM 110
- (Output 111
- Optional Optional FMIO 119
- 1.8 Program Control 122
- 1.9 Task Management 125
- Currently executed step 128
- Currently paused step 129
- 1.10 Position Operation 130
- Position 137
- Optional Optional PSIZ 141
- X 100 (%) 152
- Optional Optional GRP 155
- Optional Optional DFTL 161
- Optional Optional SLTL 162
- Optional Optional GTTL 163
- Optional Optional DFWK 164
- Optional Optional SLWK 165
- Optional Optional GTWK 166
- Optional Optional DFIF 173
- Optional Optional SOIF 174
- Optional Optional SEIF 175
- Optional Optional GTIF 176
- Optional Optional SVXX 177
- Prohibited PE 177
- Optional Optional MOVP 178
- Optional Optional MOVL 179
- Optional Optional MVPI 180
- Optional Optional MVLI 181
- Start position 182
- Position origin 182
- End position 182
- Optional Optional STOP 183
- Optional Optional PUSH 185
- Center angle 191
- Center position 192
- Optional Optional PBND 193
- Distance CP 193
- Optional Optional TMPI 194
- Optional Optional TMLI 195
- Optional Optional PTRQ 196
- Ratio CC 196
- Optional Optional IFXX 199
- Data CP 199
- Optional Optional DWXX 202
- 1.15 Multi-Branching 204
- Optional Optional WHXX 205
- Prohibited Prohibited WSXX 206
- Optional Optional SYST 210
- Optional Optional GARM 211
- 1.17 Communication 212
- Optional Optional TMRD 214
- Optional Optional SCHA 216
- Character 216
- 1.18 String Operation 217
- Optional Optional SPUT 220
- Optional Optional STR 221
- Data CC 221
- Optional Optional STRH 222
- Optional Optional SLEN 225
- Optional Optional BGPA 226
- Palletizing 226
- Optional Optional PAPN 227
- Pattern 227
- Optional Optional PAST 229
- (Position 229
- Optional Optional PAPS 230
- Optional Optional PSLI 233
- (Count) CP 233
- Optional Optional PCHZ 234
- Optional Optional ACHZ 237
- added to 246
- 1.1 CP Operation 250
- All-axis parameter 251
- CP-operation 251
- 1.2 PTP Operation 252
- 2. Arm System 253
- : Area accessibly only 254
- : Area accessibly only by 254
- 3. Coordinate System 261
- 3.2 Load Coordinate System 263
- 3.3 Tool Coordinate System 267
- –50, Zb = 150, Rb = 0 272
- 50, Zb = 200, Rb = 180 272
- 5. Soft Limits 274
- 2. PATH/PSPL Commands 280
- 3. CIR/ARC Commands 280
- 1. How to Use 281
- 2. Palletizing Setting 281
- A. 3-point teaching method 283
- PX-axis direction pitch 284
- Teach position data No. 100 284
- PY-axis direction pitch 284
- 3. Palletizing Calculation 287
- 4. Palletizing Movement 288
- 5. Program Examples 290
- : 20, zigzag count: 4 291
- 1. Basic Frame 294
- 2. Ladder Statement Field 295
- 3. Points to Note 295
- OUTR301 295
- OUTR302 295
- 4. Program Example 296
- OUTR314 296
- TIMR900 296
- 0.5 SEC 296
- Chapter 7 Multi-Tasking 297
- 3. Program Switching 299
- Appendix 300
- 1 m (1000 mm) 303
- Controller end 303
- Connector not 303
- Control 304
- List of Parameters 307
- 1. I/O Parameters 308
- 3. Axis-Specific Parameters 320
- travel at 323
- 4. Driver Card Parameters 324
- for phase-W current 328
- 5. Encoder Parameters 330
- 6. I/O-Slot Card Parameters 331
- 7. Other Parameters 332
- 8. Manual Operation Types 337
- Trouble Report Sheet 374
- INTELLIGENT ACTUATOR 375
- Catalog No.: ME0119-7A 377
Produits connexes et manuels pour Matériel Iai-america XSEL-KX
Matériel Iai-america TT-C3 Manuel d'utilisateur
(364 pages)
(364 pages)
Matériel Iai-america XSEL-S Manuel d'utilisateur
(544 pages)
(544 pages)
Matériel Iai-america PSEP Manuel d'utilisateur
(116 pages)
(116 pages)
Matériel Iai-america MSEP Manuel d'utilisateur
(296 pages)
(296 pages)
Matériel Iai-america ASEL Manuel d'utilisateur
(468 pages)
(468 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.633 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels