Iai-america XSEL-QX Manuel d'utilisateur télécharger pdf (Page 508)

484

Appendix

(In the panel window, the three digits after “E” indicate an error number.)

Error No. Error name Description, action, etc.

601 EMG logic error There may be a broken pin inside the controller, among other reasons.

602 ENB logic error There may be a broken pin inside the controller, among other reasons.

603 Drive-source cutoff relay DET (MELT) error The drive-source cutoff relay may have fused.

604 Power-supply board CPU ready OFF error A ready status of the power-supply board cannot be confirmed.

605 Forced discharge error Abnormal forced discharge. The drive-source cutoff relay may be abnormal. The

power must be reconnected.

606 Regenerative discharge error Abnormal regenerative discharge. The power must be reconnected.

607 Motor power-source voltage low error Low voltage was detected in the motor power circuit.

608 Power-supply board FRCDCSTR-ON timeout error Power-supply board FRCDCSTR-ON could not be confirmed within the specified time.

609 Power-supply board RBONSTR-ON timeout error Power-supply board RBONSTR-ON could not be confirmed within the specified time.

60A Power-supply board RBONSTR-OFF timeout error Power-supply board RBONSTR-OFF could not be confirmed within the specified time.

60B Power-supply board FRCDCSTR-OFF timeout error Power-supply board FRCDCSTR-OFF could not be confirmed within the specified

time.

60C Power-system overheat error An overheated power-supply board, regenerative resistor, etc., was detected. The

power must be reconnected.

60D Slave board CPU ready OFF error (other than power supply) A ready status of the driver board, etc. (other than power-supply board) cannot be

confirmed.

60E Dynamic brake ON/OFF timeout error Dynamic brake ON/OFF cannot be confirmed within the specified time.

60F Power-supply board synchronous send timing error 1

(CPSDBSYER)

A communication failure occurred between the power-supply board and FPGA (main).

610 Power-supply board synchronous send timing error 2

(CPCLKER)

A communication failure occurred between the power-supply board and FPGA (main).

611 Power-supply board synchronous communication LRC error A communication failure occurred between the power-supply board and FPGA (main).

612 Power-supply board synchronous communication timeout error A communication failure occurred between the power-supply board and FPGA (main).

613 Driver synchronous communication driver read error A communication failure occurred between the driver board and FPGA (main).

614 Driver synchronous communication LRC error A communication failure occurred between the driver board and FPGA (main).

615 Driver synchronous communication toggle error A communication failure occurred between the driver board and FPGA (main).

61A Mounted-SIO watchdog timer error The mounted-SIO CPU system is abnormal.

61B Mounted-SIO parameter data error There is an invalid mounted-SIO parameter. Check I/O parameter Nos. 201 to 224.

61C Mounted-SIO parameter transfer format error The mounted-SIO parameter transfer format is invalid.

61D Mounted-SIO other slave error An error occurred in the mounted-SIO CPU. Record or save the detailed information

of the error list.

61E Mounted-SIO F-send/receive queue overflow error (M) An overflow was detected in the FIFO (FPGA) for main CPU-mounted-SIO

communication.

61F Mounted-SIO control command PUT disable error FIFO (FPGA)-FULL was detected at mounted-SIO control command PUT.

620 Mounted-SIO control command completion timeout error Completion of the mounted-SIO control command cannot be confirmed after the

specified time.

621 Mounted-SIO logic error A logic error in mounted-SIO control.

1 2 ... 503 504 505 506 507 508 509 510 511 512 513 ... 557 558

Commentaires sur ces manuels

Pas de commentaire

Iai-america XSEL-QX Manuel d'utilisateur Page 508

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Iai-america XSEL-QX